Siemens H-compact PLUS Operating Instructions Manual Download Page 67

Page: 67 / 83

Spare Parts

10.9 Terminal box 1XE1...

WOGeneric TEAAC / 2008
Siemens AG Operating Instructions 1.03 1RQ671...-Z

part

Description

part

Description

4.30

Locking ring

4.61

Inner bearing cover

4.35

Grease slinger

4.85

Grease feed

4.40

Cylindrical-roller bearing (floating bearing)

4.94

Fastening elements

4.50

Bearing housing

6.00

End shield, non-drive end

[ID 1052.01]

10.9

Terminal box 1XE1...

Spare parts

The neutral box only contains the neutral point. It is not permitted to install any additional

equipment.
The base plate is screwed on and is made out of steel. It is not permitted to use it as a cable

entry plate. If the terminal box is to be used as a connection box following conversion, a

brass plate should be used as the cable entry plate.
Conversion may only be undertaken following consultation with the person responsible for

the safety of the equipment and only original parts should be used.

Summary of Contents for H-compact PLUS




















































































Search results

Summary of Contents for H-compact PLUS

Reviews:

Related manuals for H-compact PLUS

Brands by name

Popular brands

Siemens H-compact PLUS, Operating Instructions Manual

Search results

Summary of Contents for H-compact PLUS

Reviews:

Related manuals for H-compact PLUS

Brands by name

Popular brands