Siemens Gigaset M 101 Data Operating Instructions Manual Download Page 37

Page: 37 / 37

Tips & tricks, settings

appendix.fm5

16.4.99

Gigaset V.24 Adapter dt/eng:A30853-X400-B104-3-74D1

Miscellaneous

Faxes are distorted when sent

with

ELSA Microlink 56k

and

WinFax 8.0 software.

Incorrect driver for voice func-

tions set under WinFax 8.0.

During installation, WinFax 8.0

requires a modem driver to be

selected for voice functions; the

Generic / Rockwell Fax/Voice

driver is to be used here accord-

ing to ELSA AG.

Fault

Cause

Solution

Monitor fault when Gigaset

M101 Data is active (e.g. slight

flickering or moiré effect).

DECT HF wanted signal is influ-

encing the monitor.

Move Gigaset M101 Data along

the longitudinal axis until the in-

terference disappears. Move Gi-

gaset M101 Data further away

from the monitor.

A slight humming can be heard

in the loudspeakers connected

to the sound card when Gigaset

M101 Data is active.

DECT HF wanted signal is de-

modulated by the analog com-

ponents of the sound card or

the amplifiers of active speakers

and thus produces a humming

sound.

Move Gigaset M101 Data along

the longitudinal axis until the in-

terference disappears. Move Gi-

gaset M101 Data further away

from the sound card/loudspeak-

ers.

Fault

Cause

Solution

Issued by
Information and Communication Products
Hofmannstraße 51, D-81359 München

Right of modification reserved.

Siemens Aktiengesellschaft

http://www.siemens.de/gigaset

Ref. no.: A30853-X400-B104-3-74D1
Printed in Germany

04/99

Summary of Contents for Gigaset M 101 Data






































Search results

Summary of Contents for Gigaset M 101 Data

Reviews:

Related manuals for Gigaset M 101 Data

Brands by name

Popular brands

Siemens Gigaset M 101 Data, Operating Instructions Manual

Search results

Summary of Contents for Gigaset M 101 Data

Reviews:

Related manuals for Gigaset M 101 Data

Brands by name

Popular brands