Siemens Gigaset M 101 Data Operating Instructions Manual Download Page 34

Page: 34 / 37

Tips & tricks, settings

appendix.fm5

16.4.99

Gigaset V.24 Adapter dt/eng:A30853-X400-B104-3-74D1

When

"AVM/Eumex"

is set, the special features of the AVM

proprietary (company-specific) protocol are taken into consider-

ation. In this case the speed settings are not compliant with AT

Hayes commands.

Support

Updates and news on the Internet

www.siemens.com/pc-communication-support

Notes on sending faxes directly from the PC

You may encounter problems if your PC program uses Class 1

fax mode. Class 1 does not support any delays in signal runt-

imes which are necessary for switching to radio mode.

Class 2 mode, on the other hand, is not as sensitive as Class 1.

However, interference can still occur due to a bad radio link. If

you have problems with this setting, start the configuration pro-

gram and check the transmission quality under

Connection

. This

can be changed by moving the Gigaset M101 Data unit slightly.

Summary of Contents for Gigaset M 101 Data






































Search results

Summary of Contents for Gigaset M 101 Data

Reviews:

Related manuals for Gigaset M 101 Data

Brands by name

Popular brands

Siemens Gigaset M 101 Data, Operating Instructions Manual

Search results

Summary of Contents for Gigaset M 101 Data

Reviews:

Related manuals for Gigaset M 101 Data

Brands by name

Popular brands