Siemens Gigaset M 101 Data Operating Instructions Manual Download Page 31

Page: 31 / 37

Tips & tricks, settings

appendix.fm5

16.4.99

Gigaset V.24 Adapter dt/eng:A30853-X400-B104-3-74D1

If the computer was not restarted, the following window ap-

pears:

If file/printer sharing has not yet been activated, you can activate

this feature, see "Sharing files" on page 32.

In the final window, select

Finish

and click

to answer the

questions. You should now see a window titled Direct Cable

Connection with the status

Accessing %1!s

The message

CLIENT

should appear a number of times in

the terminal program of the connected PC.

If this is not the case, repeat this procedure on another PC.

If the message

Client

does not appear, try the following:

●

Close the Direct Cable Connection window

●

Activate the task manager via <

CTRL

> <

ALT

> <

DEL

>. Se-

lect the task “

Rnaapp

” and end it by clicking

End Task

●

Repeat step 2 and step 3.

If this is unsucessful, the problems may have a different source.

Summary of Contents for Gigaset M 101 Data






































Search results

Summary of Contents for Gigaset M 101 Data

Reviews:

Related manuals for Gigaset M 101 Data

Brands by name

Popular brands

Siemens Gigaset M 101 Data, Operating Instructions Manual

Search results

Summary of Contents for Gigaset M 101 Data

Reviews:

Related manuals for Gigaset M 101 Data

Brands by name

Popular brands