Siemens Gigaset M 101 Data Operating Instructions Manual Download Page 36

Page: 36 / 37

Tips & tricks, settings

appendix.fm5

16.4.99

Gigaset V.24 Adapter dt/eng:A30853-X400-B104-3-74D1

Hardware problems (PC, modem, ISDN TA.):

The modem parameter request

function is not working or is not

correct.
For example, under Win 95 with

<Start><Settings><Control

Panel><Modem Proper-

ties><Diagnostics><Details>

Windows is not respecting the

AT Hayes conditions.

None

Technically specified time de-

lays that are not supported by

the modem’s driver software.

None

Data transmission with

Xmodem is very slow.

Xmodem is operating in half-du-

plex mode. After every data

package, the transmitting page

waits for acknowledgement.

The 20-30 ms signal delay per

data block on the DECT inter-

face significantly reduces the

transmission speed.

Use another transmission proto-

col, e.g. Zmodem.

Laplink 7.0 is not working.

Data transmission is switched

during transmission. AT Hayes

commands are not used for

this.

None

Fault

Cause

Solution

Fault

Cause

Solution

PABX

(telecommunications

system) cannot be configured

via a Gigaset M101 Data.

PABX configuration is not com-

patible with AT Hayes .

Configure Gigaset M101 Data in

direct mode (e.g with

9600,8,N,1).

In the case of the system, the

baud rate is switched with an in-

ternal command set that is not

compatible with AT Hayes.

None

ELSA TagGo2000 / ISDN

con-

figuration not possible.

----------------------------

Configure the modem with a di-

rectly connected serial cable.

The

ELSA TanGo 2000

terminal

adapter cannot be used under

AOL

No appropriate modem profile

is available.

Tests have shown that an oper-

ative X.75 connection is set up

with the modem profile "ISDN

ELSA TLV34 X.75 64,000".

Timers such as "

Heliowatt

" can-

not be programmed.

Incorrect protocol set.

Set Gigaset M101 Data to 300

bps direct connection. Data

flow setting: without.

The

ACER ISDN T30

terminal

adapter cannot be operated un-

der

AOL

with the initialisation

string specified in the manual.

The initialisation string is incor-

rect.

The character "/" must be re-

placed by a "~".

The Hagenuk

Speed Dragon

terminal adapter cannot be

used with the software RVS-

COM.

Commands that are not com-

patible with Hayes are trans-

ferred with the connection.

Set the Gigaset M101 Data to

115,000 bps direct connection,

see "PC - PC direct cable con-

nection: via RS232/V.24 inter-

face" on page 25

Summary of Contents for Gigaset M 101 Data






































Search results

Summary of Contents for Gigaset M 101 Data

Reviews:

Related manuals for Gigaset M 101 Data

Brands by name

Popular brands

Siemens Gigaset M 101 Data, Operating Instructions Manual

Search results

Summary of Contents for Gigaset M 101 Data

Reviews:

Related manuals for Gigaset M 101 Data

Brands by name

Popular brands