Siemens Gigaset M 101 Data Operating Instructions Manual Download Page 19 | Manualshive

Page: 19 / 37

background image

LEDs and buttons

19

gigam101.fm5

21.4.99

Gigaset V.24 Adapter dt/eng:A30853-X400-B104-3-74D1

LEDs and buttons

There are two LEDs and a black button on the front of the Gigas-

et M101 Data unit.

Both button functions

Setting a Basis to logon mode

Press the button on a powered base-type device for 10 seconds.

The two LEDs blink in sequence, thus indicating that the device

is in logon mode. Logon mode is automatically deactivated after

successful logon or after 10 minutes: the blinking stops.

Resetting the device to the factory default

Press and hold down the button on the device that has been dis-

connected from the mains. Connect the device to the power

supply while holding the button down. LED 2 lights up after 10

seconds. This LED goes out in another 10 seconds indicating

that the reset operation has been successful. The button can

then be released.

LED 1: Gigaset M101 Data status

LED 1 indicates stand-by mode:

LED 2: data transfer

LED 2 indicates the status of the transmission route on the

V.24/RS232 interface:

LED 1 blinks

The station is searching for the part-

ner or has not been registered.

LED 1 is constantly il-

luminated

The partner was found, the transmis-

sion route is on stand-by.

LED 2 off

No data transfer

LED 2 flickers

Data transfer active

«
...
17
18
19
20
21
...
»

Summary of Contents for Gigaset M 101 Data






































Reviews:

No comments

Related manuals for Gigaset M 101 Data

Brand: M2M Pages: 9

Brand: Ubee Pages: 9

Brand: C-Data Pages: 26

Brand: Gbord Pages: 8

Speed Touch 591s

Brand: Alcatel Pages: 184

Brand: Teletronics International Pages: 57

Brand: Cypress Semiconductor Pages: 33

Brand: Aaeon Pages: 72

Brand: Lanner Pages: 38

Brand: Allied Telesis Pages: 34

Brand: ZALMAN Pages: 16

Brand: Chase Research Pages: 114

Brand: ETAS Pages: 84

Brand: AC Infinity Pages: 24

Brand: Dave Embedded Systems Pages: 79

Brand: TRENDnet Pages: 10

Brand: Beckhoff Pages: 84

Brand: FOR-A Pages: 37

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands