Siemens CP 1243-8 IRC Operating Instructions Manual Download Page 55

Page: 55 / 140

Configuration and operation

4.6 Configuration in STEP 7 V5

CP 1243-8 IRC
Operating Instructions, 06/2015, C79000-G8976-C385-01

4.6.4

Exporting configuration data

Exporting the configuration data using SDB text files

After completing the configuration of the proxy in STEP 7 V5 and in the SINAUT

configuration tool, the specific configuration data for the telecontrol communication of the

proxy is stored in system data blocks (SDBs) just as with TIM modules.
Follow the steps below to export the configuration data of the proxy:
1.

Open the SINAUT diagnostics and service tool with the relevant project.

Select the proxy.

Open the menu "SINAUT" > "SDB display".

Figure 4-7

Opening the "SDB display" dialog

The "SDB display" dialog opens.
With the drop-down list box "System data blocks" you can display the contents of the

individual SDBs. This is however not relevant for exporting the configuration data.

Summary of Contents for CP 1243-8 IRC













































































































































Search results

Summary of Contents for CP 1243-8 IRC

Reviews:

Related manuals for CP 1243-8 IRC

Brands by name

Popular brands

Siemens CP 1243-8 IRC, Operating Instructions Manual

Search results

Summary of Contents for CP 1243-8 IRC

Reviews:

Related manuals for CP 1243-8 IRC

Brands by name

Popular brands