manualshive.com logo in svg

Siemens CP 1243-8 IRC, Operating Instructions Manual

Share
Download
Siemens CP 1243-8 IRC Operating Instructions Manual Download Page 24

Application and properties 

 

1.7 Configuration examples 

 

CP 1243-8 IRC 

24

 

Operating Instructions, 06/2015, C79000-G8976-C385-01 

Inter-station communication between stations 
Inter-station communication is possible for stations connected to the same master station. 
For the inter-station communication between stations, the master station forwards the 

messages of the sending station to the receiving station. 

Telecontrol communication - Ethernet 

In the sample configuration shown, an S7-300 and two S7-1200 stations communicate with a 

master station SINAUT ST7cc/ST7sc. 
The CPs are connected via their Ethernet interface. 
The connection to the Ethernet network, in this example a fiber-optic cable, is implemented 

using SCALANCE X switches. Copper cable is also possible as the medium. 

 

Figure 1-2 

Communication via an Ethernet network (optical medium) 

Summary of Contents for CP 1243-8 IRC













































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands