manualshive.com logo in svg

Siemens CP 1243-8 IRC, Operating Instructions Manual

Share
Download
Siemens CP 1243-8 IRC Operating Instructions Manual Download Page 21

 

Application and properties 

 

1.6 Connection to various network types 

CP 1243-8 IRC 
Operating Instructions, 06/2015, C79000-G8976-C385-01 

21

 

●

 

The SIM card and PIN belonging to the mobile wireless contract 
The SIM card is inserted in the TS module GSM. 
With mobile wireless contracts in which the network provider does not assign a PIN, no 

PIN is configured for the CP in STEP 7 V5. 

●

 

Local availability of a mobile wireless network in the range of the station. 

1.6

 

Connection to various network types 

Supported network types 

The CP makes telecontrol communication with the ST7 protocol possible via the network 

types listed below. 
Connection via the Ethernet interface of the CP: 

●

 

IP-based communication via the Ethernet interface the CP: 
–

 

Industrial Ethernet 
Communication in the LAN (copper / fiber-optic cable) 

–

 

Internet 
Communication via the Internet 

–

 

IP-based wireless network 
Communication via IP-based wireless networks 

●

 

Connection via the serial interface of the CP 
With communication via the network types listed below, in addition to the CP a TS 

module, modem or router must be used. 
–

 

Dedicated line (incl. analog wireless network) 
Communication via dedicated lines or analog wireless networks 

–

 

Analog dial-up network 
Communication via the analog dial-up network 

–

 

ISDN network 
Communication via the ISDN network 

–

 

Mobile wireless network 
IP-based communication via mobile wireless networks (GSM/GPRS, UMTS, LTE) 

The following table provides an overview of the supported network types, the devices to be 

used in the station and in the communications partner and the protocols or services used. 

Summary of Contents for CP 1243-8 IRC













































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands