manualshive.com logo in svg

Siemens CP 1243-8 IRC, Operating Instructions Manual

Share
Download
Siemens CP 1243-8 IRC Operating Instructions Manual Download Page 51

 

Configuration and operation 

 

4.6 Configuration in STEP 7 V5 

CP 1243-8 IRC 
Operating Instructions, 06/2015, C79000-G8976-C385-01 

51

 

●

 

Connection mode (RS232) 
Configuration in the "Interfaces“ tab 
–

 

MSC station 
The serial interface is configured as an Ethernet interface. The communication is 

handled using the MSC protocol. The proxy is configured to connect to the Internet as 

an MSC station via a DSL router. 

–

 

Neutral 
The serial WAN interface of the proxy is set to the connection mode "Neutral“ if 

communication is handled via a dial-up network or dedicated line. 

 

Figure 4-2 

Properties dialog, "Interfaces" tab with WAN interface to which a dial-up network is 

connected. 

●

 

Modems for dial-up networks 
In addition to the TIM for communication of the CP via dial-up networks, the required TS 

modules for the serial WAN interface of the proxy can be selected in theInterfaces tab, 

see below. 

●

 

AT strings for TS modules 
AT strings were added for the TS modules, see below. 

●

 

No SMS configuration 
The configuration of the sending of SMS messages is not possible for the proxy in 

STEP 7. 
You can arrange for the sending of SMS messages in STEP 7 Basic for every data point. 

Summary of Contents for CP 1243-8 IRC













































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands