manualshive.com logo in svg

Siemens CP 1243-8 IRC, Operating Instructions Manual

Share
Download
Siemens CP 1243-8 IRC Operating Instructions Manual Download Page 41

 

Installation, connecting up, commissioning 

 

3.2 Installing, connecting up and commissioning 

CP 1243-8 IRC 
Operating Instructions, 06/2015, C79000-G8976-C385-01 

41

 

Installation location 

 

 

NOTICE 
Installation location 
The module must be installed so that its upper and lower ventilation slits are not covered, 

allowing adequate ventilation. Above and below the device, there must be a clearance of 25 

mm to allow air to circulate and prevent overheating. 
Remember that the permitted temperature ranges depend on the position of the installed 

device. You will find the permitted temperature ranges in the section Technical data 

(Page 105). 

 

 

Device position / permitted temperature range 

Installation location 

Horizontal installation of the rack 

 

Vertical installation of the rack: 

 

Connecting up the device and installing it 

Below you will find a description of mounting the CP and a TS module on a DIN rail. For 

mounting the control panel of the S7-1200 refer to /1/ (Page 135). 

 

 

CAUTION 

Connection with power off 
Only wire up the S7-1200 with the power turned off. 

 

 

CAUTION 

Slot to the left of the CP only for TS module 
To the left of the CP 1243-8 IRC only a TS module can be inserted. 
If you insert another module to the left of the CP, this will damage this module. 

 

Summary of Contents for CP 1243-8 IRC













































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands