Siemens CF62 Service Manual Download Page 41

Page: 41 / 42

SIEMENS

CF62 Level 2 Service Manual

SSMC MD CCQ

41 of 42

Internal Service Use Only

Siemenes Shanghai Technical Support Center

Final Inspection:

The final inspection contains:

1. A 100% network test (location update, and set up call).

A random sample checks of:

data reset (if required)

- optical

appearance

complete function

Check if PIN-Code is activated (delete the PIN-Code if necessary).

Remark

: All sample checks must be documented.

Annex 1

Test SIM Card

There are two different “Test SIM Cards” in use:

Test SIM Card from the company

“ORGA”

Pin 1 number:       0000
PUK 1 :                 12345678
Pin 2 number:       0000
PUK 2 :                 23456789

Test SIM Card from the company

“T-D1”

Pin 1 number:          1234
PUK1 :                     76543210
Pin 2 number:           5678
PUK 2 :                    98765432

Summary of Contents for CF62









































Search results

Summary of Contents for CF62

Reviews:

Related manuals for CF62

Brands by name

Popular brands

Siemens CF62, Service Manual

Search results

Summary of Contents for CF62

Reviews:

Related manuals for CF62

Brands by name

Popular brands