Siemens CF62 Service Manual Download Page 38

Page: 38 / 42

SIEMENS

CF62 Level 2 Service Manual

SSMC MD CCQ

38 of 42

Internal Service Use Only

Siemenes Shanghai Technical Support Center

Check the charging capability

Check internal resistance and capacity of the battery.

Check battery charging capability of the mobile phone.

Check charging capability of the power supply.

Check current consumption of the mobile phone in different mode.

Visual inspection:

Check the entire board for liquid damages.

Check the entire board for electrical damages.

Check the housing of the mobile phone for damages.

SW update:

Carry out a software update and data reset according to the master tables and
operator/customer requirements.

GSM Test:

Connect the mobile/board via internal antenna (antenna coupler) to a GSM
tester.

Use a Test SIM.

Skip GSM 900/GSM1800 or GSM1900 test cases if not performed by the mobile
phone.

Summary of Contents for CF62









































Search results

Summary of Contents for CF62

Reviews:

Related manuals for CF62

Brands by name

Popular brands

Siemens CF62, Service Manual

Search results

Summary of Contents for CF62

Reviews:

Related manuals for CF62

Brands by name

Popular brands