manualshive.com logo in svg

Siemens Cerberus GW-21, Technical Manual, Page: 15 / 44

Share
Download
Siemens Cerberus GW-21 Technical Manual Download Page 15

11

Siemens Building Technologies

Cerberus Division

E1481b

06.2000

4 

CPU Board Configuration

4.1 

Introduction

On the CPU board you can find four groups of  DIL-Switches, numbered from S1 to S4.
A fifth block can be found on the expansion board if it is installed. The  DIL-Switches re-
place the jumpers that were used on the GW-01 for configuration purposes.
We will refer in this document to  DIL-Switches with a double numbering convention: the
fist number refers to the block the  DIL-Switch belongs to, the second number is the
switch position inside the block. Therefore, S1-2 means “the second  DIL-Switch on the
first block”.

Gateway configuration

Gateway configuration can be done in two alternative ways:

§

  by DIL-Switches

§

  by Flash  EPROM

Flash EPROM configuration is required when the gateway has to handle interactions
among subsystems. The Flash  EPROM can be configured using a proper software tool
provided by Cerberus Dati.

Gateway data-link

The Gateway GW-21 can be connected to various devices, and namely to:

§

  CS11 fire detection control unit, manufactured by Cerberus

§

  CS4 intrusion detection control unit, manufactured by Cerberus

§

  CC60 gas detection unit, manufactured by Cerberus

§

  Cerberus Dati CMX/CF9003, that allow I/O of digital signals

§

  Westinghouse Electronics access control devices which use the SEEP protocol

§

  Cerberus Guinard STT

§

  CCTV switching matrix, MX series, manufactured by Comerson.

§

  8x00 Allegiant CCTV switcher control system, manufactured by Burle.

§

  MK7022 Cerloop Interface

§

  Devices supplied by third parties that use Cerberus Dati Standard Protocol

(CDDL/CDSF)

§

  CC30 Door Controller manufactured by Cerberus Ristow

§

  Transliner intrusion detection control unit by Cerberus Ristow

i

Unfortunately , due to limited ROM space not all these devices can share the same
gateway. Different firmware EPROM are needed to accommodate the most common
and useful combinations of these devices. Appendix B lists the combinations available
(please also refer to latest LMS News).

A set of EPROM programs that allow connection of peripheral devices is called 

soft-

ware link

. All GW-21 links and its firmware are located on a single Flash EPROM.

Summary of Contents for Cerberus GW-21













































Reviews:

No comments