manualshive.com logo in svg

Siemens AH Series, Manual

Share
Download
Siemens AH Series Manual Download Page 23

Siemens Building Technologies, Inc

.                                                                                                                                                         P84449-003 B 

Sheet 2 of 4 

 
 

 

Table 3:   Current Ratings (AMPS)  

Maximum RMS Current with Hi dBA Setting 

Voltage 135cd 

185cd 

DC 16.0-33.0VDC 

0.356 

0.488 

FWR 16.0-33.0VRMS 

0.499 

0.705 

Maximum RMS Current with Med dBA Setting 

 Voltage 

135cd 

185cd 

DC 16.0-33.0VDC 

0.361 

0.493 

FWR 16.0-33.0VRMS 

0.509 

0.716 

Maximum RMS Current with Low dBA Setting 

Voltage 135cd 

185cd 

DC 16.0-33.0VDC 

0.356 

0.499 

FWR 16.0-33.0VRMS 

0.488 

0.705 

 

Note: 

These notification appliances are UL Listed as “Special Application.” They are intended to be used only with Siemens notification appliance circuits. 

 

WARNING:  MAKE SURE THAT THE TOTAL RMS CURRENT REQUIRED BY ALL APPLIANCES THAT ARE CONNECTED TO THE SYSTEM’S 

PRIMARY AND SECONDARY POWER SOURCES DO NOT EXCEED THE POWER SOURCES’ RATED CAPACITY OR THE CURRENT RATINGS OF 
ANY FUSES ON THE CIRCUITS TO WHICH THESE APPLIANCES ARE WIRED.  OVERLOADING POWER SOURCES OR EXCEEDING FUSE 
RATINGS COULD RESULT IN LOSS OF POWER AND FAILURE TO ALERT OCCUPANTS DURING AN EMERGENCY, WHICH COULD RESULT IN 
PROPERTY DAMAGE AND SERIOUS INJURY OR DEATH TO YOU AND/OR OTHERS.  
 
CANDELA AND SOUND OUTPUT SETTINGS: 
 

To set the candela, slide the switch to the desired setting.  The setting is indicated by the pointer and label visible on the bottom side of the lens.   
 

Figure 1: 

              Figure 2:  Showing Location of Jumper Plug 

 

135

185

 CANDELA

 POINTER

BOTTOM VIEW

 

CODE 3

HI

MED

LO

 

CANDELA

SLIDE

SWITCH

BACK VIEW

 

Factory setting is on Medium dB, Code 3 (or March Time) and 185 candela. 

WARNING:  THE AUDIBLE STROBE APPLIANCES MUST BE FIELD SET TO THE DESIRED TONE AND dBA SOUND OUTPUT LEVEL BEFORE 

THEY ARE INSTALLED.  THIS IS DONE BY PROPERLY INSERTING JUMPER PLUGS IN ACCORDANCE WITH THESE INSTRUCTIONS.  

 

 

Figure 3:  Jumper plug settings for High, Medium, Low and Code 3      

(or March Time) 

 

Figure 4:  Jumper plug setting for Continuous Horn 

 

SHOWN SET ON HIGH dB

SHOWN SET ON MED dB
SHOWN SET ON LOW dB

HI

MED

LOW

 

(Use needle nose pliers to pull and properly set the jumper plugs)

 

 

 

CODE 3

TURN PLUG 90°

 

No jumper plug is needed for continuous horn setting. 

 

However, it is recommended that the jumper plug be retained in 
the unit for future use (if needed) as shown in Figure 4.

 

 

NOTE:  

The AS-HMC must be set for Code 3 (or March Time) when used with a synchronized notification appliance circuit (NAC). 

 

 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for AH Series


























Reviews:

No comments

Brands by name

Popular brands

Load more brands