manualshive.com logo in svg

Siemens AH Series, Manual

Share
Download
Siemens AH Series Manual Download Page 16

Siemens Building Technologies, Inc. 

 

    P83519-005 

B 

8 Fernwood Road

 

 

    Sheet 

1 

of 

3 

Florham Park, New Jersey 07932 

 

                                                             

INSTALLATION INSTRUCTIONS 

AUDIBLE HORN APPLIANCES 

 

 

 

 

 

 

 

              

 
IMPORTANT – 

All audible and visual signaling appliances must be 

installed in accordance with all applicable national and local fire alarm 
codes and any other required regulatory agencies. 

 

Series AH Appliances provide a selectable Continuous or Code 3 
Horn tone when connected directly to the Fire Alarm Control Panel 
(FACP).  They can also provide a synchronized code 3 or March 
Time horn tone when connected to a notification appliance circuit 
running the Siemens sync protocol. The AH Appliances are UL Listed 
under UL Standard 464 for Audible Signal Appliances and ULC Listed 
under Standard CAN/ULC-S525-99 for Audible Signaling Appliances. 

They are listed for indoor use only

 and are equipped with a 

Universal Mounting Plate (UMP) that can be mounted to single-gang, 
double-gang, 4” square backbox, 100mm European or SHBBS 
surface backbox (See Mounting Options). 

 
AH Appliances can be field set to provide either High (HI) dBA, 
Medium (MED) dBA or Low (LO) dBA sound output.  All AH models 
are designed for use with either filtered DC or unfiltered Full-Wave-
Rectified (FWR) input voltage. All inputs are polarized for 
compatibility with standard reverse polarity supervision of circuit 
wiring by a FACP. 
 

NOTE:

  The code 3 horn incorporates the temporal pattern (1/2 

second on, 1/2 second off, 1/2 second on, 1/2 second off, 1/2 second 
on, 1-1/2 off and repeat) specified by ANSI/NFPA for standard 
emergency evacuation signaling.  

The code 3 horn shall be used 

only for fire evacuation signaling and not for any other purpose. 

 
SPECIFICATIONS

: 

 

Table 1:  UL/ULC Listed Models and Ratings 

Maximum RMS Current (AMPS) 

DC  

FWR  

Model* 

Operating Voltage 

(Special Application) 

Per UL 464 

(VDC/VRMS) 

ULC Voltage 

Range 

(VDC/VRMS) 

Lo Med Hi  Lo Med Hi 

AH 

16-33 

20-31  0.021 0.043 0.080 0.041 0.051 0.090 

* Available in red or white. 

 

Table 1A:  ULC Current Ratings 

Average Current (AMPS) 

Model ULC 

Voltage 

(VDC/VRMS) 

Lo Med Hi 

20.0 .014 

.020 

.035 

24.0 .017 

.025 

.050 

AH 

31.0 .021 

.030 

.065 

 

Table 2:  dBA Sound Output for 24VDC Models 

Reverberant dBA Per UL 464 

Anechoic Per CAN/ULC-S525-99 

Description Volume 

16.0VDC 24VDC 33.0VDC 16.0VDC 24VDC 33.0VDC 

 

Low  80 83 86 88 90 92 

Continuous 

Horn 

Medium 

85 88 91 90 95 97 

 

High  88 91 93 92 97 99 

 

Low  75 79 82 88 90 92 

Code 

3 

Horn 

or 

 

Medium 

80 84 86 90 95 97 

March 

Time* 

High  84 87 90 92 97 99 

* Available in sync mode only. 

NOTES: 

1. 

All models are UL/ULC Listed for indoor use with a temperature range of +0

°

C to +49

°

C (+32

°

F to +120

°

F) and maximum humidity of 93% 

±

 2% RH. 

Table 2A:  ULC Directional Characteristics

 

-3 dBA:  48 degrees left, 41 degrees right 
-6 dBA:  50 degrees left, 58 degrees right 

 

WARNING:  CHECK THE MINIMUM AND MAXIMUM OUTPUT OF THE POWER SUPPLY AND STANDBY BATTERY AND SUBTRACT THE 

VOLTAGE DROP FROM THE CIRCUIT WIRING RESISTANCE TO DETERMINE THE APPLIED VOLTAGE TO THE SIGNALING APPLIANCE. 

 

FOR UL APPLICATIONS THESE APPLIANCES WERE TESTED TO THE OPERATING VOLTAGE LIMITS OF 16-33 VOLTS FOR 24V MODELS 

USING FILTERED (DC) OR UNFILTERED FULL-WAVE-RECTIFIED (FWR).  DO NOT APPLY 80% AND 110% OF THESE VOLTAGE VALUES 

FOR SYSTEM OPERATION. 

 

FOR ULC APPLICATIONS THESE APPLIANCES WERE TESTED TO THE OPERATING VOLTAGE LIMITS OF 20-31 VOLTS FOR 24V MODELS 

USING FILTERED (DC) OR UNFILTERED FULL-WAVE-RECTIFIED (FWR).  APPLY 80% AND 110% OF THESE VOLTAGE VALUES FOR 

SYSTEM OPERATION. 

Summary of Contents for AH Series


























Reviews:

No comments

Brands by name

Popular brands

Load more brands