manualshive.com logo in svg

Siemens AH Series, Manual

Share
Download
Siemens AH Series Manual Download Page 2

appliances are specified, the strobe intensity shall have  

field selectable settings and shall be rated per UL Stan-

dard 1971 at 15/30/75/110 or 135/185 candela for wall 

mount and 15/30/75/95 or 115/177 candela for ceiling 

mount.  The selector switch for selecting the candela 

shall be tamper resistant.  
When synchronization is required, the appliance shall 

be synchronized using the Siemens DSC sync modules, 

FS-250 panel, XLS panel, or PAD-3 power supply with 

built-in sync protocol.  The strobes shall not drift out of 

synchronization at any time during operation.  If the sync 

module or Power Supply fails to operate, (i.e., contacts 

remain closed), the strobe shall revert to a non-synchro-

nized flash-rate.  The appliance shall also be designed 

so that the audible signal may be silenced while main-

taining strobe activation when used with Siemens syn-

chronization.
The Series AS Audible Strobe and Series AH Audible 

shall incorporate a Patented Universal Mounting Plate 

that shall allow mounting to a single-gang, double-gang, 

4-inch square, 100mm European type backboxes, or the 

SHBBS Surface Backbox.  
All notification appliances shall be listed for Special Ap-

plications.
•   Strobes are designed to flash at 1 flash per second 

minimum over their “Regulated Input Voltage Range”.  

Note that NFPA-72 specifies a flash rate of 1 to 2 

flashes per second and ADA Guidelines specify a flash 

rate of 1 to 3 flashes per second.

•   All candela ratings represent minimum effective Strobe 

intensity based on UL Standard 1971. 

Technical Information

For complete technical information, please consult the 

relevant installation sheets as well as the Siemens  

Compatibility Guide.

Model  

Number

Order Code

Wall 

Mount

Ceiling 

Mount

Mounting Options**

Agency Approvals

UL ULC CSFM FM

AS-MC-R

500-636010

X

-

A,B,D,E,F,G,J,N,R,X

X

#

#

#

AS-MC-W

500-636011

X

-

A,B,D,E,F,G,J,N,R,X

X

#

#

#

AS-HMC-R

500-636012

X

-

A,B,D,E,F,G,J,N,R,X

X

#

#

#

AS-HMC-W

500-636013

X

-

A,B,D,E,F,G,J,N,R,X

X

#

#

#

AS-MC-CR

500-636006

-

X

A,B,D,E,F,G,J,N,R,X

X

#

#

#

AS-MC-CW

500-636007

-

X

A,B,D,E,F,G,J,N,R,X

X

#

#

#

AS-HMC-CR

500-636008

-

X

A,B,D,E,F,G,J,N,R,X

X

#

#

#

AS-HMC-CW

500-636009

-

X

A,B,D,E,F,G,J,N,R,X

X

#

#

#

AS-75-R-WP

500-636016

X

-

I

X

#

#

#

AS-75-CR-WP

500-636015

-

X

I

X

#

#

#

AH-R

500-636003

X

X

A,B,D,E,F,G,J,N,R,X

X

#

#

#

AH-W

500-636004

X

X

A,B,D,E,F,G,J,N,R,X

X

#

#

#

AH-R-WP

500-636005

X

X

K

X

#

#

#

Ordering Information / Mounting Requirements / Approvals

X = listed/approved 

# = pending 

* = Refer to Data Sheet #2585 for mounting options.

Siemens Building Technologies

Fire Safety

Fire Safety
8 Fernwood Road
Florham Park, NJ 07932
Tel: (973) 593-2600
FAX: (973) 593-6670
Website: www.sbt.siemens.com/fis

7/07

5M

SFS-IG

Printed in U.S.A.

Fire Safety
2 Kenview Boulevard
Brampton, Ontario
Canada L6T 5E4
Tel: (905) 799-9937
FAX: (905) 799-9858

July 2007

New Issue

WARNING:

  PLEASE  READ  THESE  SPECIFICATIONS AND  INSTALLATION  INSTRUCTIONS  CAREFULLY  BEFORE  

USING, SPECIFYING OR APPLYING THIS PRODUCT.  FAILURE TO COMPLY WITH ANY OF THESE INSTRUCTIONS, 

CAUTIONS AND  WARNINGS  COULD  RESULT  IN  IMPROPER APPLICATION,  INSTALLATION AND/OR  OPERATION  

OF THESE  PRODUCTS  IN AN  EMERGENCY  SITUATION,  WHICH  COULD  RESULT  IN  PROPERTY  DAMAGE, AND  

SERIOUS INJURY OR DEATH TO YOU AND/OR OTHERS.

Summary of Contents for AH Series


























Reviews:

No comments

Brands by name

Popular brands

Load more brands