Siemens Building Technologies, Inc
.
P84448-003B
8 Fernwood Road
Page 1 of 1
Florham Park, New Jersey 07932
.
INSTALLATION INSTRUCTIONS
MULTI-HIGH-CANDELA AUDIBLE STROBE APPLIANCE
(CEILING MOUNT VERSION)
IMPORTANT –
All audible and visual signaling appliances must be
installed in accordance with all applicable national and local fire alarm
codes and any other required regulatory agency.
Series Audible Strobe Multi-High-Candela (AS-HMC-C) Appliance is the
industry’s first 2-wire horn strobe alarm appliance that provides two
selectable candela settings (115, 177). Siemens Audible Strobe
Appliances provide a selectable continuous or code 3 horn tone and
non-synchronized strobe when connected directly to a Fire Alarm
Control Panel (FACP). They can also provide a synchronized code 3
(or March time) horn tone and synchronized strobe when connected to
a notification appliance circuit running the Siemens sync protocol. The
AS-HMC-C Appliance is UL Listed under Standard 1971 for Emergency
Appliances for the Hearing Impaired and UL Standard 464 for Audible
Signal Appliances. This appliance is listed for
ceiling mounting and
indoor use only
and is equipped with a universal mounting plate
(UMP) that can be mounted to single-gang, double-gang, 4” backbox,
100mm European backbox or SHBBS surface backbox (See wiring and
mounting information). The AS-HMC-C appliance uses a xenon
flashtube with solid state circuitry enclosed in a polycarbonate lens to
provide maximum visibility and reliability for effective visible signaling.
The AS-HMC-C Appliance can be field set to provide either high (HI)
dBA, medium (MED) dBA or low (LO) dBA sound output.
This model is designed for use with either filtered DC (VDC) or
unfiltered full-wave-rectified (FWR) input voltage. All inputs are
polarized for compatibility with standard reverse polarity supervision of
circuit wiring by a FACP.
NOTE:
The Code 3 temporal pattern (1/2 second on, 1/2 second off,
1/2 second on, 1/2 second off, 1/2 second on, 1-1/2 off and repeat) is
specified by ANSI and NFPA 72 for standard emergency evacuation
signaling.
The Code 3 Horn should be used only for fire evacuation
signaling and not for any other purpose.
NFPA 72/ANSI 117.1 conform to ADAAG Equivalent Facilitation
Guidelines in using fewer, higher intensity strobes within the same
protected area.
NOTE:
Refer to P/N 315-096363 for the maximum number of
appliances on a single notification appliance circuit.
.
SPECIFICATIONS:
Table 1: UL Ratings
Model
Operating Voltage (Special Application)
Per UL 1971
(VDC/VRMS)
Strobe
Candela
(cd)
Mounting
Options
AS-HMC-C* 16.0-33.0
115/177
A,B,C,D
* Available in red and white.
Table 2: dBA Sound Output
Description
Volume
Reverberant Per UL 464
16.0VDC
24.0VDC
33.0VDC
Low 80 83 86
Continuous Horn
Medium
85
88
91
High
88 91 93
Low 75 79 82
Code 3 Horn
Medium
80
84
86
(or March Time)**
High
84
87
90
** Available in sync mode only.
NOTES:
1.
Strobe will produce 1 flash per second over the Input Voltage range.
2.
This strobe/horn model meets the required light distribution patterns defined in UL 1971.
3.
This model is UL Listed for indoor use with a temperature range of +32ºF to +120ºF (0ºC to +49ºC) and maximum humidity of 85% RH. The effect of
shipping and storage temperatures shall not adversely affect the performance of the appliance when it is stored in the original cartons and not
subjected to misuse or abuse.
When calculating the total current: Use Table 3 to determine the highest value of “RMS Current” for an individual AS Appliance then multiply the value by
the total number of AS Appliances. Be sure to add the currents for any other appliances powered by the same source and include any required safety
factors.
THESE APPLIANCES WERE TESTED TO THE VOLTAGE LIMITS OF 16.0-33.0 VOLTS FOR 24V MODELS USING FILTERED DC OR UNFILTERED
FULL-WAVE-RECTIFIED VOLTAGE. DO NOT APPLY VOLTAGE OUTSIDE OF THIS RANGE.
Note:
Refer to the installation instructions for the appropriate NAC to find the maximum allowed voltage drop. Use this value along with the current draw
for the appliance to determine the allowable wire resistance. The maximum wire resistance between strobes shall not exceed 35 ohms.
This appliance is not designed to be used on coded systems in which the applied voltage is cycled on and off.
CANDELA SETTING WILL DETERMINE THE CURRENT DRAW OF THE PRODUCT.
