manualshive.com logo in svg

Siemens AH Series, Manual

Share
Download
Siemens AH Series Manual Download Page 1

AS/AH

AS Audible Strobe Appliances and AH Audibles

ENGINEER AND ARCHITECT SPECIFICATIONS

•   UL listed.  ULC, CSFM, and FM pending.
•  ADA/NFPA/UFC/ANSI Compliant
•   Wall mount models are available with Field Selectable Candela 

Settings of 15/30/75/110cd or 135/185cd (Multi-Candela models) 

•   Ceiling mount models are available with field selectable candela 

settings of 15/30/75/95cd or 115/177cd (Multi- 

candela ceiling models)

•  Selectable Continuous Horn or Temporal (Code 3).
•   3 Selectable dBA settings (99, 95 and 90 dBA) in both tones
•  Weatherproof models are available for outdoor use
•   Strobes can be synchronized using the Siemens DSC sync 

modules, FS-250 panel, XLS panel, or PAD-3 power supply with 

built-in sync protocol.

•   Fast installation with IN/OUT screw terminals using #12 to #18 

AWG wires

Description

The Siemens 2-wire Series AS Audible Strobe Appli-

ances and Series AH Audibles offer more features with 

low current draw.
Strobe options for wall mount models include the Sie-

mens MC multi-candela wall strobes with field selectable 

candela settings of 15/30/75/110cd, or the high intensity 

HMC strobe with field selectable 135/185cd.
Ceiling mount models incorporate Siemens MC multi-

candela ceiling strobe with field selectable settings of 

15/30/75/95cd or the high intensity HMC strobe with field 

selectable settings of 115/177cd.
The audible provides a selectable choice of either a con-

tinuous horn or temporal pattern (Code 3) when constant 

voltage from a Fire Alarm Panel (FACP) is applied. Each 

tone has 3 dBA settings from which to choose.  
When used with the Siemens DSC sync modules, 

FS-250 panel, XLS panel, or PAD-3 power supply with 

built-in sync protocol, synchronization of the continuous 

horn tone provides the temporal (code 3) tone (man-

dated by NFPA 72) simultaneously for all audible appli-

ances.  This ensures a distinct temporal (code 3) pattern 

when 2 or more audibles are within hearing distance.  If 

not synchronized the temporal sound could overlap and 

not be distinctive.  At the same time the strobes will be 

synchronized.  This provides the ability to comply with 

ADA guidelines concerning photosensitive epilepsy and 

the NFPA standards when installing  

2 or more visual appliances within the field of view all of 

this plus the ability to silence the audible is achieved by 

using only 2 wires. 

Engineering Specifications

The notification appliances shall be Siemens Series 

AS Audible Strobe appliances and Series AH Audible 

appliances or approved equals.  The Series AS Audible 

be listed for UL Standard 1971 (Emergency Devices for 

the Hearing-Impaired) for Indoor Fire Protection Service. 

The Series AH Audible shall be UL Listed under Stan-

dard 464 (Fire Protective Signaling).   Both shall meet 

the requirements of FCC Part 15 Class B.  All inputs 

shall be compatible with standard reverse polarity su-

pervision of circuit wiring by a Fire Alarm Control Panel 

(FACP). 
The audible portion of the appliance shall have a mini-

mum of three (3) field selectable settings for dBA levels 

and shall have a choice of continuous or temporal (Code 

3) audible outputs.
The strobe portion of the appliance shall produce a flash 

rate of one (1) flash per second over the Regulated 

Voltage Range and shall incorporate a Xenon flashtube 

enclosed in a rugged Lexan® lens.  The Series AS  

shall be of low current design.  Where Multi-Candela 

CATALOG SHEET

2578

AH-W

AS-MC-CW

AS-MC-R

AH-R

Summary of Contents for AH Series


























Reviews:

No comments

Brands by name

Popular brands

Load more brands