manualshive.com logo in svg

Siemens Advance Network Gateway, User Manual, Page: 56 / 72

Share
Download
Siemens Advance Network Gateway User Manual Download Page 56

48  

••

  Troubleshooting

2000590-001

ANCB Description

The ANCB (Advance Network Communication Board) is the communica-
tions electronics for the unit. The ANCB plugs into to PCI slot located on
the power supply assembly. A bracket fastens it to the chassis. See Fig-
ure 2-4 Power Supply/ANCB Assembly.

J 1 2

J 4

1 0 B a s e 2

1 0 B a s e T

A D H - A
J 1 0
D a t a N E T -

A D H - B
J 1 1
D a t a N E T - B

C o n f i g   P o r t
R S 2 3 2
5 7 . 6   K B

B o a r d
R E S E T

O p e r a t i o n   L E D S

J 5

J 2   ( N /A   f o r

 

A N G - E N   O p e r a t i o n )

Jumpers J10 & J11 select the ANG_EN network interface provided to
connector J4.

J10 connects Port1 on J4 to either the Advance Data Hiway (ADH) or
Advance DataNET Channel A interface.

J11 connects Port2 on J4 to either the Advance Data Hiway (ADH) or
Advance DataNET Channel B interface. J10 & J11 are configured for
Advance Data Hiway (ADH) on the ANG_EN board.

J2 is used to select the 10Base2-termination resistor. If the 10Base2 port
is not used the jumper is placed between pins 3 & 4. If the 10Base2 port
is connected as an end point device (ANG-DN) then the jumper is placed
between pins 1 & 2.

See ANCB LEDs Description and Operation, page 49.

Description

Figure 3-1. ANCB Board

J10 & J11
Connections

J5 Connector

More Information

Summary of Contents for Advance Network Gateway









































































Reviews:

No comments