manualshive.com logo in svg

Siemens Advance Network Gateway, User Manual, Page: 31 / 72

Share
Download
Siemens Advance Network Gateway User Manual Download Page 31

2000590-001

Installation  

••

  23

Ethernet Connections

The DataNET Gateway connects to the Ethernet local area network via
the RJ-45 STP connector located on the topside of the ANCB.

Read the following notes.

1.  The 10BASE-T data cable requires a minimum of two twisted pair

(transmit pair and a receive pair). Wire used should conform to the
AT&T D-inside wire (DWI&PDS), or IBM Type 3 or better twisted-pair
cable specifications, or Category 3 or 5 data grade cabling or better.

2.  The maximum length of a 10BASE-T data cable can not exceed 328

feet (100 meters). Typically to increase the distance each ANG_EN
will connect to a hub or other type of repeater/medium converter.

3.  The cable should be terminated at both ends with RJ-45 STP male

connectors. The table below shows the RJ-45 wiring connections for
the ANG_EN end of the cable.

Pin No.

MDI Function

1

TX+

2

TX-

3

RX+

4

NC

5

NC

6

RX-

7

NC

8

NC

Description

Figure 2-7. RJ-45 STP
Connector

Before You Begin

Summary of Contents for Advance Network Gateway









































































Reviews:

No comments