manualshive.com logo in svg

Siemens Advance Network Gateway, User Manual, Page: 29 / 72

Share
Download
Siemens Advance Network Gateway User Manual Download Page 29

2000590-001

Installation  

••

  21

Data Hiway Connections, 

Continued

For technical information on the Data Hiway refer to Appendix A in the
Optichrom Advance Library Set, Volume 2, Board Installation and Strap-
ping Manual.

Step

Action

1. 

Place the ANG_EN AC Power Supply (Mains) circuit
breaker to OFF. On the ANG_EN Power Supply Assembly
place toggle ON/OFF switch to OFF.

WARNING

Placing the Power Supply Assembly toggle ON/OFF switch
to OFF does not remove the main voltage to the J1 termi-
nals. To remove all input power to the ANG_EN, the AC
Power (Mains) to the ANG_EN needs to be shut off.

2. 

Route the Data Hiway cable to the ANG_EN in accordance
with national or local electrical codes and regulations; see
Figure 2-1.

To make the Data Hiway connections easier we have made it a remov-
able connector. Simply grasp the top portion of the connector and pull it
straight out from the base connector; see Figure 2-6.

Do not plug the Data Hiway connector in until you have set the loop and
unit number; see Chapter 3. Data Communications Setup.

More Information

Instructions

Installation Note

CAUTION

Summary of Contents for Advance Network Gateway









































































Reviews:

No comments