manualshive.com logo in svg

Siemens 6GT2002-0HD01, Operating Instructions Manual, Page: 9 / 72

Share
Download
Siemens 6GT2002-0HD01 Operating Instructions Manual Download Page 9

 

SIMATIC RF170C 
Operating Instructions, 02/2022, J31069-D0176-U001-A6-7618 

9

 

Description

 

2 

2.1

 

Area of application and features 

Area of application 

The RF170C communication module is a SIMATIC S7 module. It can be plugged into the 

ET 200pro distributed I/O station. The ET 200pro is operated via PROFIBUS DP V1 or 

PROFINET IO. An S7-300/-400/-1200/-1500 can be used as the controller. 
Via the interface module of the ET 200pro, the RF170C can communicate will all DP masters 

that behave according to the standard IEC 61784-1:2002 Ed1 CP 3/1. The DP master must 

support DP-V1 (acyclic services). 
The RF170C can be used as a central I/O device in an ET 200pro with a suitable interface 

module. Thanks to its degree of protection IP67, the RF170C can be installed and operated 

direct at the process without any additional protective housing. 

 

Figure 2-1 

RF170C communication module 

When operating the communications modules on a SIMATIC S7, convenient function blocks 

are available to you. 
The following RFID devices and optical readers can be operated with the RF170C: 
•

 

RF200 (normal addressing) 

•

 

RF300 (standard addressing) 

•

 

MOBY D 

•

 

MOBY U (normal addressing) 

•

 

MV400, MV500 

•

 

MV320 

Summary of Contents for 6GT2002-0HD01









































































Reviews:

No comments