manualshive.com logo in svg

Siemens 6GT2002-0HD01, Operating Instructions Manual, Page: 31 / 72

Share
Download
Siemens 6GT2002-0HD01 Operating Instructions Manual Download Page 31

 

Parameter settings 

 

5.2 Configuration via STEP 7 (Basic/Professional) 

SIMATIC RF170C 
Operating Instructions, 02/2022, J31069-D0176-U001-A6-7618 

31

 

Table 5- 1 

Parameters in the "Module parameters" parameter group 

Parameter 

Parameter value 

Default value 

Description 

User Mode 

Ident profile/RFID 

standard profile 

FB 45 / FC 45 

FB 55 / FC 55 

Ident profile/RFID 

standard profile 

Selection depends on the communications 

module and Ident system being used. With this 

parameter you select the block:  
•

 

Ident profile/RFID standard profile: 
The program block for the Ident profile/RFID 

standard profile is used on the controller.  

•

 

FB 45 / FC 45: 
Single tag mode FB 45 (PROFIBUS/PROFINET) 

or FC 45 (PROFIBUS) is used on the 

controller.  

•

 

FB 55 / FC 55: 
Multitag mode. FB 55 (PROFIBUS/PROFINET) 

or FC 55 (PROFIBUS) is used on the 

controller. 

MOBY Mode 

RF200/RF300/RF600; 

MV4x0; MOBY U/D 

MOBY I/E 

MV3xx 

Freeport protocol 

RF300 filehandler 

RF200/RF300/RF600

; MV4x0; MOBY U/D 

Selection depends on the communications 

module and Ident system being used. With this 

parameter, you set the mode of the 

communications module. 
•

 

RF200/RF300/RF600; MV4x0; MOBY U/D 

•

 

MOBY I/E 

•

 

MV3xx 

•

 

Freeport protocol 

•

 

RF300 filehandler

1)

 

Normal addressing: The transponder is 

addressed with physical addresses.  

Transmission  

speed 

19.2 kBd 

57.6 kBd 

115.2 kBd 

115.2 kBd 

Selection depends on the communications 

module and Ident system being used. With this 

parameter you set the transmission speed 

between the communications module and 

reader.  

When the RFID reader is connected: After 

changing the transmission speed, the reader 

must be turned off and on again (cycle power).  

When an optical reader is connected: The 

transmission speed selected here must match 

the transmission speed selected in the firmware 

of the reader. 

Diagnostics 

messages 

None 

Hard errors 

None 

Selection depends on the communications 

module and Ident system being used. With this 

parameter you set whether hardware 

diagnostics messages will be reported. 
•

 

None: 
Apart from standard diagnostics, no other 

alarms are generated. 

•

 

Hard errors: 
Critical hardware errors are reported by the 

S7 diagnostics. 

Summary of Contents for 6GT2002-0HD01









































































Reviews:

No comments