manualshive.com logo in svg

Siemens 6GT2002-0HD01, Operating Instructions Manual, Page: 24 / 72

Share
Download
Siemens 6GT2002-0HD01 Operating Instructions Manual Download Page 24

Mounting 

 

3.3 Mounting the terminating module 

 

SIMATIC RF170C 

24

 

Operating Instructions, 02/2022, J31069-D0176-U001-A6-7618 

3.3

 

Mounting the terminating module 

Introduction 

The ET 200pro is terminated with the terminating module. To operate the ET 200pro the 

terminating module must be mounted.  

Requirements 

•

 

The last communications module of the ET 200pro has been mounted. 

•

 

All communications modules are screwed onto the rack. 

Procedure 

Follow the steps below to mount the terminating module: 
1.

 

Plug the terminating module onto the rack. 

2.

 

Move the terminating module to the left to the last communications module. 

 

Figure 3-3 

Mounting the terminating module 

3.

 

Screw the terminating module onto the rack (2 cross-head screws on the fronte, torque 

1.5 Nm). 
Make sure that all other connection modules are already screwed to the communications 

modules. 

3.4

 

Set the PROFIBUS address and the terminating resistor 

You will find detailed information on setting the terminating resistor in the “ET 200pro 

distributed I/O device (

https://support.industry.siemens.com/cs/ww/en/view/21210852

)“ 

operating instructions. 

Summary of Contents for 6GT2002-0HD01









































































Reviews:

No comments