manualshive.com logo in svg

Siemens 6GT2002-0HD01, Operating Instructions Manual, Page: 17 / 72

Share
Download
Siemens 6GT2002-0HD01 Operating Instructions Manual Download Page 17

 

Description 

 

2.2 Design 

SIMATIC RF170C 
Operating Instructions, 02/2022, J31069-D0176-U001-A6-7618 

17

 

2.2.3

 

Maximum configuration 

Mechanical maximum configuration 

The maximum configuration of an ET 200pro is reached when one of the rules outlined 

below applies:  

Table 2- 2 

Mechanical maximum configuration 

Properties 

Rule 

Number of modules 

Maximum 9 RF170Cs 

Width of the ET 200pro 

max. 1 meter mounting width (without rack) 

Electrical maximum configuration  

Elec/encoder supply 1L+ 
•

 

Supplies power to the internal electronics of the modules and to readers connected 

externally 

•

 

Electrically isolated from the backplane bus of the ET 200pro and PROFIBUS DP 

Table 2- 3 

Electrical maximum configuration 

Properties 

Rule 

Elec / encoder supply 1L+ 

max. 5 A per ET 200pro station 

(must not be exceeded with connected readers) 

 

 

 

Note 
Configuring the ET 200pro 

The maximum electrical setup can be checked with the TIA Selection Tool. We recommend 

use of the tool because the maximum setup cannot be achieved with all reader 

configurations. 
You will find the tool on the Internet on the page of the “Siemens homepage 

(

http://w3.siemens.com/mcms/topics/en/simatic/tia-selection-tool/Pages/tab.aspx

)“. 

 

Summary of Contents for 6GT2002-0HD01









































































Reviews:

No comments