manualshive.com logo in svg

Siemens 6GT2002-0HD01, Operating Instructions Manual, Page: 6 / 72

Share
Download
Siemens 6GT2002-0HD01 Operating Instructions Manual Download Page 6

Introduction 

 

  

 

SIMATIC RF170C 

6

 

Operating Instructions, 02/2022, J31069-D0176-U001-A6-7618 

Conventions 

The following terms/abbreviations are used synonymously in this document: 

 

Reader 

Write/read device (SLG). optical handheld reader 

Transponder, tag 

Data carrier, mobile data storage, MDS 

Communications module, CM 

Interface module, IM 

Registered trademarks 

SIMATIC ®, SIMATIC RF ®, MOBY ®, RF MANAGER ® and SIMATIC Sensors ® are registered 

trademarks of Siemens AG.  

Recycling and disposal 

The products are low in harmful substances, can be recycled and meet the requirements of 

the Directive 2012/19/EU for disposal of waste electrical and electronic equipment (WEEE). 
Do not dispose of the products at public disposal sites. 
For environmentally compliant recycling and disposal of your electronic waste, please contact 

a company certified for the disposal of electronic waste or your Siemens representative. 
Note the different country-specific regulations. 

Summary of Contents for 6GT2002-0HD01









































































Reviews:

No comments