background image

SD66 

 

8

PARTS LIST 

Siemens Amplifying and Reducing Relay, Model Series 66 

Drawing 4297PL 

Rev 7/82

 

 
 
 
 
 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

All product designations may be trademarks or product names of Siemens Energy & Automation, Inc. or other supplier companies 
whose use by third parties for their own purposes could violate the rights of the owners.

 

 
Siemens Energy & Automation, Inc. assumes no liability for errors or omissions in this document or for the application and use of information in 
this document.  The information herein is subject to change without notice. 
 
Procedures in this document have been reviewed for compliance with applicable approval agency requirements and are considered sound 
practice. Neither Siemens Energy & Automation, Inc. nor these agencies are responsible for repairs made by the user. 

IMPORTANT 

Service Parts Kits are available for 
servicing the instrument. Contact 
Siemens for available kits; refer to the 
Product Support section of this 
instruction. Some parts in this Parts 
List may not be available for separate 
purchase. 
 
* Recommended on-hand spare parts. 
Always specify range, serial number, 
or other nameplate information when 
ordering spare parts. 

StockCheck.com

Downloaded from StockCheck.com

Summary of Contents for 66 Series









Reviews: