manualshive.com logo in svg

Siemens 1PQ8, Operating Instructions & Installation Instructions

Share
Download
Siemens 1PQ8 Operating Instructions & Installation Instructions Download Page 86

The following information is provided regarding the state of the winding insulation:
● Is the winding head insulation conductively contaminated?
● Has the winding insulation absorbed moisture?
As such, you can determine whether the machine needs commissioning or any necessary 

measures such as cleaning and/or drying the winding:
● Can the machine be put into operation?
● Must the windings be cleaned or dried?
Detailed information on testing and the limit values can be found here:
"Testing the insulation resistance and polarization index"  (Page 45) 

8.8

Decommissioning the machine

NOTICE
Damage as a result of an extended period out of service
If the machine is going to be out of service for longer than six months, then take the necessary 

measures for preservation and storing. Otherwise damage to the machine will result. 

Record the decommissioning steps. This log will be useful upon recommissioning.

8.9

Re-commissioning the machine

When you re-commission the machine, proceed as follows:
● Study the record made when the machine was decommissioned, and reverse the measures 

that were taken for conservation and storage.

● Perform the measures listed in the "Commissioning" section.

See also

Start-up (Page 73)

8.10

faults

8.10.1

Inspections in the event of faults

Natural disasters or unusual operating conditions, such as overloading or short circuit, are 

faults that overload the machine electrically or mechanically.
Immediately perform an inspection after such faults.     

Operation
8.8 Decommissioning the machine

SIMOTICS TN Series N-compact  1LH8

86

Operating Instructions 06/2017

Summary of Contents for 1PQ8













































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands