Siemens 1PQ8 Operating Instructions & Installation Instructions Download Page 5

Page: 5 / 140

Table of contents

Introduction.................................................................................................................................................11
1.1

About these instructions.........................................................................................................11

1.2

Compiling personal documents..............................................................................................11

Safety information.......................................................................................................................................13
2.1

Information for the nominated person in control of the electrical installation.........................13

2.2

The five safety rules...............................................................................................................13

2.3

Qualified personnel................................................................................................................14

2.4

Safe handling.........................................................................................................................14

2.5

Electrostatic sensitive devices...............................................................................................16

2.6

Interference immunity.............................................................................................................17

2.7

Influence on the line power supply through a strongly irregular torque..................................17

2.8

Interference voltages when operating the converter..............................................................17

2.9

Electromagnetic fields when operating electrical power engineering installations.................18

Description..................................................................................................................................................19
3.1

Comparison of IEC and GOST (D47) standards....................................................................20

Preparations for use...................................................................................................................................25
4.1

Safety-related aspects to consider when configuring the plant..............................................25

4.2

Observing the operating mode...............................................................................................25

4.3

Ensuring cooling.....................................................................................................................25

4.4

Cooling water quality..............................................................................................................25

4.5

Thermal motor protection.......................................................................................................26

4.6

Interlock circuit for anti-condensation heating (option)...........................................................27

4.7

Support base for IM B5 construction type..............................................................................27

4.8

Noise emissions.....................................................................................................................27

4.9

Rotational speed limit values.................................................................................................28

4.10

Phase synchronization during supply system switching........................................................28

4.11

Voltage and frequency fluctuations during line operation......................................................28

4.12

System-inherent frequencies.................................................................................................29

4.13

Torsional loading of the drive train due to faults in the electrical supply................................29

4.14

Transport and storage............................................................................................................29

4.14.1

Transport markings................................................................................................................30

4.14.2

Checking the delivery.............................................................................................................30

SIMOTICS TN Series N-compact 1LH8

Operating Instructions 06/2017

Summary of Contents for 1PQ8













































































































































Search results

Summary of Contents for 1PQ8

Reviews:

Brands by name

Popular brands

Siemens 1PQ8, Operating Instructions & Installation Instructions

Search results

Summary of Contents for 1PQ8

Reviews:

Brands by name

Popular brands