manualshive.com logo in svg

Siemens 1PQ8, Operating Instructions & Installation Instructions

Share
Download
Siemens 1PQ8 Operating Instructions & Installation Instructions Download Page 40

4.15.4

Converter operation on a grounded network

NOTICE
Damage resulting from protective conductor currents
When the machine is operated on a converter with current limiter, but without ground-fault 

monitoring, protective conductor currents of up to 1.7 times the external conductor current 

can arise if there is a ground fault on the output side. Neither the PE conductors of normally 

rated multi-core connecting cables nor the PE connecting points of normal terminal boxes 

are suitable for this purpose. Material damage can result.
● Use an appropriately sized PE conductor.
● Connect the PE conductor to the grounding terminal on the motor enclosure.

4.15.5

Insulated bearings when operating the converter

If the machine is operated from a low-voltage converter, insulated bearings are fitted at the 

NDE and an insulated encoder with insulated bearings (option).   
Comply with the plates on the machine relating to bearing insulation and possible bridges.   

①

Driving machine

④

Insulated bearings

②

Motor

⑤

Insulated tachometer fitting

③

Coupling

 

 

Figure 4-2

Schematic representation of a single drive

NOTICE
Bearing damage
The bearing insulation must not be bridged. Bearing currents can damage bearings.
● Also for subsequent installation work, such as the installation of an automatic lubrication 

system or a non-insulated vibration sensor, make sure that the bearing insulation cannot 

be bridged.

● Contact the Service Center, if necessary.

Preparations for use
4.15 Converter operation

SIMOTICS TN Series N-compact  1LH8

40

Operating Instructions 06/2017

Summary of Contents for 1PQ8













































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands