Side-Power SX-35/140 Installation Manual Download Page 20 | Manualshive

Page: 20 / 24

background image

20

5630

6

2019

-

SX35 & SX50

MC_0081

Checklist for SX Thrusters

EN

�.......... Propeller is fastened correctly to the shaft.

�.......... Propeller turns freely in tunnel.

�.......... Primer and anti-fouling have been applied to the gearhouse and propeller but NOT on the

anode or the gearhouse lid where the propeller is fastened.

�.......... Correct drive direction as per controlpanel.

�.......... The bolts holding the thruster are tightened correctly.

�.......... The bolts holding the motor to its bracket are tightened correctly.

�.......... All electrical connections are clean, dry and tight, and the correct cable, fuse and main

switch size.

�.......... No water leakage around hull penetrated studs

�.......... Check that there is no electrical connection between the electromotor body and positive

terminal on the motor, and between the electromotor body and the negative (A1) terminal on

the motor with an ohm meter.

The thruster has been installed as per the instructions in this manual and all points in checklist above have been controlled.

Signed: .........................................................................................

Date: .............................................................................................

Extra pre-delivery tests by installer / yard who does not use other quality control systems !

Thruster type: ................................................................................................................................................................................................

Serial number:...............................................................................................................................................................................................

Date of delivery:.............................................................................................................................................................................................

Correct drive direction as per controlpanel: ..................................................................................................................................................

The compartment for the thruster has been isolated from general bilge water and has no obvious or suspected risks for ﬂ ooding:

......................................................................................................................................................................................................................

......................................................................................................................................................................................................................

......................................................................................................................................................................................................................

Other comments by installer: ........................................................................................................................................................................

.......................................................................................................................................................................................................................

.......................................................................................................................................................................................................................

......................................................................................................................................................................................................................

«
...
18
19
20
21
22
...
»

Summary of Contents for SX-35/140

























Reviews:

No comments

Related manuals for SX-35/140

Brand: Yamaha Pages: 497

Brand: Gigabyte Pages: 93

Brand: Biostar Pages: 54

C5535 DSPShield

Brand: Texas Instruments Pages: 49

Brand: National Semiconductor Pages: 13

Brand: Freetech Pages: 79

Brand: Mini-Itx Pages: 174

Brand: Advantech Pages: 116

Brand: ON Semiconductor Pages: 8

dsPICDEM MCHV-3

Brand: Microchip Technology Pages: 68

Brand: Gigabyte Pages: 96

Brand: OMS Pages: 11

Brand: Gigabyte Pages: 96

Brand: Intel Pages: 29

WAFER-BW-N4-R10

Brand: IEI Technology Pages: 136

GENE-9455 Rev.B

Brand: Aaeon Pages: 64

Brand: Avalue Technology Pages: 83

Brand: Gigabyte Pages: 41

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands