Side-Power SE 60/185 S2 Installation And User Manual Download Page 7

Page: 7 / 24

5693

2019

SE60/185 S2

MG_0028

Anode holding screw

Anode

lock nut

washer

propeller

drive pin

Motor Installation

1. Insert drive pin on the motor shaft and insert the coupling to the motor shaft.

2. Install the motor onto the motor bracket ensuring both the couplings and the drive shafts have locked together.

(NB: depending on your coupling

you may need to wiggle the motor into place. Ensure the connection couplings are engaging correctly. The motor can be placed in all

directions on the motor bracket. However, ensure the cable terminals are accessible for electrical installation later.)

3. Fasten the motor loosely to the motor bracket with the provided bolts. (

NB: If you are installing the motor at an angle of more than 30º oﬀ

vertical, the motor will require separate/ additional support.)

4. Fasten the bolts holding the motor to the motor bracket with the above torque.

5. Check the drive shafts engage by rotating the propeller. It is required the propeller can rotate via hand power.

(NB: Rotating the propellers can

be hard because of the gear reduction and the motor.)

6. Apply the gear leg and propeller with antifouling designed for propellers. Do not apply to the propeller drive shaft, the anodes or the end of the gear

leg facing the propellers.

Only in shallow installations in workboat and fi shing boats we recommend protecting the propeller by installing a grid in the tunnel opening.

(NB: Keep

the grid conﬁ guration to a minimum to ensure water ﬂ ow for the thruster is not signiﬁ cantly aﬀ ected. Be aware that any grid conﬁ guration

will change the eﬀ ectiveness of the thruster and circular proﬁ le steel will decrease thrust signiﬁ cantly.)

(NB: The motor must be covered to avoid dust from fabrication/ maintenance operation entering the motor or the solenoids. After fabrication

maintenance operations have ceased the cover must be removed before operating the thruster.)

MC_0043

Please refer to the graphic for special considerations relating to your model

MG_0029

2 - 3

Drive pin

Coupling

Motor coupling

Gasket

Turn gear leg

shaft so the

motor coupling

will fit

Top

Bottom

Fasten bolts

17Nm (12,4lb/ft)

Summary of Contents for SE 60/185 S2

























Search results

Summary of Contents for SE 60/185 S2

Reviews:

Related manuals for SE 60/185 S2

Brands by name

Popular brands

Side-Power SE 60/185 S2, Installation And User Manual

Search results

Summary of Contents for SE 60/185 S2

Reviews:

Related manuals for SE 60/185 S2

Brands by name

Popular brands