Side-Power SE 60/185 S2 Installation And User Manual Download Page 14 | Manualshive

Page: 14 / 24

background image

14

5693

2

2019

-

SE60/185 S2

MC_0033

Checklist for DC and IP Thrusters

EN

�.......... Propeller is fastened correctly to the shaft.

�.......... Propeller turns freely in tunnel.

�.......... The anode holding screw is tightened well with thread glue.

�.......... Anti-fouling have been applied to the gearhouse and propeller but NOT on the anode or the

gearhouse lid where the propeller is fastened.

�.......... Correct drive direction as per controlpanel.

�.......... The bolts holding the gearhouse and motorbracket together are tightened correctly.

�.......... The bolts holding the motor to its bracket are tightened correctly.

The thruster has been installed as per the instructions in this manual and all points in checklist above have been controlled.

Signed: .........................................................................................

Date: .............................................................................................

Extra pre-delivery tests by installer / yard who does not use other quality control systems !

Thruster type: ................................................................................................................................................................................................

Serial number:...............................................................................................................................................................................................

Date of delivery:.............................................................................................................................................................................................

Correct drive direction as per controlpanel: ..................................................................................................................................................

The compartment for the thruster has been isolated from general bilge water and has no obvious or suspected risks for ﬂ ooding:

......................................................................................................................................................................................................................

......................................................................................................................................................................................................................

......................................................................................................................................................................................................................

Other comments by installer: ........................................................................................................................................................................

.......................................................................................................................................................................................................................

.......................................................................................................................................................................................................................

......................................................................................................................................................................................................................

«
...
12
13
14
15
16
...
»

Summary of Contents for SE 60/185 S2

























Reviews:

No comments

Related manuals for SE 60/185 S2

SBC81206 Series

Brand: AXIOMTEK Pages: 74

870 Extreme3 R2.0

Brand: ASROCK Pages: 17

Brand: LITETRONICS Pages: 2

Brand: SOYO Pages: 95

Brand: Wintech Pages: 5

GeForce 8300 (MI-A78U-8309)

Brand: XFX Pages: 26

Brand: NXP Semiconductors Pages: 12

X58 PLATINUM SLI - Motherboard - ATX

Brand: MSI Pages: 74

Brand: JETWAY Pages: 40

Brand: JETWAY Pages: 57

Brand: PRIZM Pages: 9

STEVAL-PLC001V1

Brand: ST Pages: 42

Brand: Intel Pages: 26

Brand: JETWAY Pages: 47

ADIS1650 PCBZSeries

Brand: Analog Devices Pages: 11

Brand: AOpen Pages: 11

Brand: BCM Pages: 57

Brand: Gigabyte Pages: 96

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands