manualshive.com logo in svg

SICK SIM2000ST-E, Operating Instructions Manual, Page: 35 / 38

Share
Download
SICK SIM2000ST-E Operating Instructions Manual Download Page 35

Feature

Parameter

Supply voltages

X2: 700 mA max
X4, X5: 700 mA total

Battery type

CR 1632

Housing material

Aluminum die cast

Housing color

Uncoated aluminum or light blue (RAL 5012) depending on ver‐
sion

Protection class

III

Weight

1630 g

Dimensions (W x D x H)

225.5 x 132.5 x 83 mm

11.4

Ambient data

Feature

Parameter

Electromagnetic compati‐
bility

IEC 61000-6-2:2016 / EN IEC 61000-6-2:2019
IEC 61000-6-4:2018 / EN IEC 61000-6-4:2019
IEC 61131-9:2013-09

Vibration resistance

IEC 60068-2-6: 2007 (sine)
IEC 60068-2-64:2008 (broadband)

Shock resistance

EN 60068-2-27:2009-05

Electrical safety

IEC 61010-1:2010 + COR:2011 + A1:2016,
mo A1:2016 / COR1:201

Enclosure rating

IP20 (device must be installed in a control cabinet of at least IP54
rating)

Ambient conditions

Operation site

Height position

Contamination rating

Use inside buildings
max. 2,000 m
1

Ambient operating temper‐
ature

0 °C ... +60 °C, when the described mounting requirements are
taken into account,

see "Mounting the device", page 15

Storage temperature

-20 °C ... +70 °C

Permissible relative humid‐
ity

90%, non-condensing

TECHNICAL DATA 

11

8025454/1BLK/2021-03-30 | SICK

O P E R A T I N G   I N S T R U C T I O N S | SIM2000ST-E

35

Subject to change without notice

Summary of Contents for SIM2000ST-E







































Reviews:

No comments