SICK SIM2000ST-E Operating Instructions Manual Download Page 15 | Manualshive

Page: 15 / 38

SICK SIM2000ST-E Operating Instructions Manual Download Page 15

5

Mounting

5.1

Overview of mounting procedure

NOTE

The mounting procedure described here for the device meets the requirements for use
in the target system.
Additional or different requirements may become necessary in the laboratory and dur‐
ing preparation, and should be taken into account as necessary,

see "Commissioning",

. If you have any questions or anything remains unclear in this regard, please

contact our service team.

•

Install the device.

•

Connect the cables.

•

Connecting peripheral devices.

•

Connecting the voltage supply.

5.2

Scope of delivery

•

SIM 2000ST-E

•

4 x grounding screw

•

4 x toothed lock washer

•

Safety note

NOTE

The device is equipped with spring terminals as standard.

5.3

Preparing for mounting

Mounting requirements

•

Select the mounting site:
Plan space requirements and sufficient distance from other devices.
Be aware of the possibility of heat dissipation.

•

Unpack the device and allow to acclimatize to avoid formation of condensation.

Preparing for mounting

1.

Place the device at the mounting site.

2.

Mark the mounting holes.

3.

Proceed to drill the mounting holes.

5.4

Mounting the device

Mounting the device

1.

Set the device on the mounting site.

2.

Fasten device with at least two M5 screws (max. 6 Nm) on opposite device sides
and corresponding washers.

NOTICE

Use self-locking or lock nuts on mounting sites that are exposed to vibrations to prevent
the holding plates from loosening.

MOUNTING

5

8025454/1BLK/2021-03-30 | SICK

O P E R A T I N G I N S T R U C T I O N S | SIM2000ST-E

15

Subject to change without notice

«
...
13
14
15
16
17
...
»

Summary of Contents for SIM2000ST-E







































Reviews:

No comments