manualshive.com logo in svg

SICK deTem4 Core Ex, Operating Instructions Manual

Share
Download
SICK deTem4 Core Ex Operating Instructions Manual Download Page 62

Column
height

Suitable for
number of
beams

Suitable for
beam separa‐
tion

Type code

Part number

1,285 mm

4

300 mm

PM3S13-00430040

1040626

Complementary information

Observe the information on deflector mirrors, particularly on changing the scanning
range.

Further topics

•

"Deflector mirrors", page 61

14.7

Device columns

Table 28: Ordering information for device columns

Column height

Max. installation
length

Type code

Part number

985 mm

965 mm

PU3H96-00000000

2045490

1185 mm

1165 mm

PU3H11-00000000

2045641

1285 mm

1265 mm

PU3H13-00000000

2045642

1570 mm

1550 mm

PU3H15-00000000

2068813

1740 mm

1720 mm

PU3H17-00000000

2045643

2040 mm

2020 mm

PU3H21-00000000

2045644

2270 mm

2250 mm

PU3H22-00000000

2045645

2420 mm

2400 mm

PU3H24-00000000

2045646

14.8

Cleaning agent

Table 29: Cleaning agent ordering information

Part

Part number

Anti-static plastic cleaner

5600006

Lens cloth

4003353

14.9

Test rods

Table 30: Ordering information, test rods

Part

Part number

Test rod 30 mm

2022602

Test rod holder

2052249

14 

ACCESSORIES

62

O P E R A T I N G   I N S T R U C T I O N S | deTem4 Core

8020453/14Q7/2020-04-27 | SICK

Subject to change without notice

Summary of Contents for deTem4 Core Ex





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands