Shuttle HOT-591P User Manual Download Page 41 | Manualshive

Page: 41 / 45

background image

40

PCI IRQ Activated by

This item sets the method by which the PCI bus recognize that an IRQ service is being
requested by a device. You should never change the default configuration unless advised
otherwise by your System's manufacturer.
The Choice: Level(default) and Edge.

PCI Latency Timer

The number of clocks programed in the PCI Latency Timer represents the guaranteed time
slice allocated to the 82C598AT, after which it must complete the current data transfer
phase and surrender the bus as soon as its bus grant is removed.

The PCI Latency Timer is used to guarantee to the PCI agents a minimum amount of the
system resource.

The default setting is 64 PCI clocks.

Assign IRQ For VGA

This item allows the user to set VGA IRQ Routing table Enabled or Disabled.

«
...
39
40
41
42
43
...
»

Summary of Contents for HOT-591P














































Reviews:

No comments

Related manuals for HOT-591P

Brand: Yamaha Pages: 82

Brand: Texas Instruments Pages: 52

Brand: Linear Technology Pages: 16

Brand: ZiLOG Pages: 41

Brand: JETWAY Pages: 47

Brand: Raptor Pages: 59

Brand: ASROCK Pages: 6

Brand: AKM Pages: 30

Brand: Intel Pages: 110

Brand: ST Pages: 82

Brand: Humandata Pages: 8

Brand: JETWAY Pages: 56

Brand: Albatron Pages: 57

Brand: ON Semiconductor Pages: 7

Brand: Mercury Pages: 57

Brand: Ublox Pages: 22

Brand: Gigabyte Pages: 80

TPS25944X635EVM

Brand: Texas Instruments Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands