manualshive.com logo in svg

Shure ANI22-BLOCK, User Manual, Page: 33 / 35

Share
Download
Shure ANI22-BLOCK User Manual Download Page 33

9/12/17, 9(22 AM

Shure Publications | User Guides | ANI22

Page 33 of 35

http://pubs.shure.com/guide/ANI22/en-US

European representatives. For contact information please visit www.shure.com

Specifications

Analog Connections

Inputs

Active Balanced

ANI22-XLR

(2) XLR connector

ANI22-BLOCK (2) 6-pin block connector

Outputs Impedance Balanced ANI22-XLR

(2) XLR connector

ANI22-BLOCK (2) 3-pin block connector

Network Connections (Dante Digital Audio)

(1) RJ45

Channel Count: 2 Inputs, 2 Outputs

Polarity

Non-inverting, any input to any output

Power Requirements

Power over Ethernet (PoE), Class 0. (PoE Plus compatible).

Power Consumption

11W, maximum

Weight

672  g (1.5 lbs)

Dimensions

H x W x D

4 x 14 x 12.8 cm (1.6 x 5.5 x 5.0 in.)

control application

HTML5 Browser-based

Operating Temperature Range

−

6.7°C (20°F) to 40°C (104°F)

Storage Temperature Range

−

29°C (-20°F) to 74°C (165°F)

Thermal Power Dissipation

Maximum 12.1 W (41.3 BTU/hr)

Summary of Contents for ANI22-BLOCK




































Reviews:

No comments