manualshive.com logo in svg

Shure ANI22-BLOCK, User Manual, Page: 26 / 35

Share
Download
Shure ANI22-BLOCK User Manual Download Page 26

9/12/17, 9(22 AM

Shure Publications | User Guides | ANI22

Page 26 of 35

http://pubs.shure.com/guide/ANI22/en-US

< REP 

xx

 AUDIO_MUTE OFF >

Get Device Audio Mute

Command String:
< GET DEVICE_AUDIO_MUTE >

ANI22 Response:
< REP DEVICE_AUDIO_MUTE ON >

< REP DEVICE_AUDIO_MUTE OFF >

The ANI22 will respond with one of these
strings.

Set Device Audio Mute

Command String:
< SET DEVICE_AUDIO_MUTE ON >

< SET DEVICE_AUDIO_MUTE OFF >

< SET DEVICE_AUDIO_MUTE TOGGLE >

Send one of these commands to the ANI22.

ANI22 Response:
< REP DEVICE_AUDIO_MUTE ON >

< REP DEVICE_AUDIO_MUTE OFF >

The ANI22 will respond with one of these
strings.

Get Analog Output Gain Switch

Command String:
< GET 

xx

 AUDIO_OUT_LVL_SWITCH >

Where 

xx

 is ASCII channel number: 00, 03,

or 04.

ANI22 Response:
< REP 

xx

 AUDIO_OUT_LVL_SWITCH

LINE_LVL >

< REP 

xx

 AUDIO_OUT_LVL_SWITCH

AUX_LVL >

< REP 

xx

 AUDIO_OUT_LVL_SWITCH

MIC_LVL >

The ANI22 will respond with one of these
strings.

Set Analog Output Gain Switch

Command String:
< SET 

xx

 AUDIO_OUT_LVL_SWITCH

LINE_LVL >

< SET 

xx

 AUDIO_OUT_LVL_SWITCH

AUX_LVL >

< SET 

xx

 AUDIO_OUT_LVL_SWITCH

MIC_LVL >

Where 

xx

 is ASCII channel number: 00, 03,

or 04. Send one of these commands to the
ANI22.

ANI22 Response:
< REP 

xx

 AUDIO_OUT_LVL_SWITCH

LINE_LVL >

< REP 

xx

 AUDIO_OUT_LVL_SWITCH

The ANI22 will respond with one of these
strings.

Summary of Contents for ANI22-BLOCK




































Reviews:

No comments