4
Order code: 40102
Polar 300 Hybrid IP65 Moving Head
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance of
this manual or any unauthorized modification to the device.
●
Never let the power cord come into contact with other cables! Handle the power cord and all
connections with the mains with particular caution!
●
Never modify, bend, mechanically strain, put pressure on, pull or heat up the power cord.
●
Never strain the cable. There must always be sufficient cable going to the device. Otherwise, the
cable will be damaged, which can cause serious damage.
●
Never remove warning or informative labels from the unit.
●
Never use anything to cover the ground contact.
●
Never lift the device holding it by the projector-head, as the mechanics may be damaged. Always
hold the device by the transport handles.
●
Never place any material over the LEDs or lens.
●
Never look directly into the light source.
●
Never leave any cables lying around.
●
Never use the device during thunderstorms, unplug the device immediately.
●
Never leave various parts of the packaging (plastic bags, polystyrene foam, nails, etc.) within
children’s reach, as they are potential sources of danger.
●
Do not insert objects into air vents.
●
Do not open the device and do not modify the device.
●
Do not connect this device to a dimmer pack.
●
Do not switch the device on and off in short intervals, as this will reduce the device’s life.
●
Do not touch the device’s housing bare-handed during its operation (housing becomes very hot).
Allow the device to cool for at least 5 minutes before handling.
●
Do not shake the device. Avoid brute force when installing or operating the device.
●
Only operate the device after having checked if the housing is firmly closed and all screws are tightly
fastened.
●
Only operate the device after having familiarized with its functions.
●
Avoid flames and do not put close to flammable liquids or gases.
●
Always allow a free air space of at least 80 cm around the unit for ventilation.
●
Always disconnect power from the mains, when device is not used or before cleaning! Only handle
the power cord holding it by the plug. Never pull out the plug by tugging the power cord.
●
Make sure that the device is not exposed to extreme heat or dust.
●
Make sure that the available voltage is not higher than stated on the rear panel.
●
Make sure that the power cord is never crimped or damaged. Check the device and the power
cord from time to time.
●
Make sure that the core diameter of extension cords and power cords is sufficient for the required
power consumption of the device.
●
If the lens or LEDs are obviously damaged, they need to be replaced to prevent their functions from
being impaired, due to cracks or deep scratches.
●
If the external cable is damaged, it has to be replaced by a qualified technician.
●
If device was dropped or struck, disconnect mains power supply immediately. Have a qualified
engineer inspect for safety before operating.
●
If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not
switch it on immediately. The arising condensation water might damage your device. Leave the
device switched off until it has reached room temperature.
●
If your Showtec device fails to work properly, discontinue the use immediately. Pack the unit securely
(preferably in the original packing material), and return it to your Showtec dealer for service.
●
For adult use only. The device must be installed beyond the reach of children. Never leave the unit
running unattended.
●
Never attempt to bypass the thermostatic switch or fuses.
●
For replacement use fuses of same type and rating only.
●
This device is heavy. When handling, use a two-person lift to prevent injury.
●
The user is responsible for correct positioning and operating of the device. The manufacturer will not
accept liability for damages caused by the misuse or incorrect installation of this device.
●
This device falls under protection class I. Therefore it is essential to connect the yellow/green
conductor to earth.
Summary of Contents for 40102
