background image

 

Document Number: 0004593 
Rev: 1 

Page 2 

 

Introduction 

The ShoreScreen Power Curtain system is designed to be assembled to a boathouse structure. The assembly process involves leg 
bolts and mounting brackets to the boathouse, hanging the curtain sides, attaching the corner components, and pairing the wireless 
remotes with the controller. 
 
The assembly process explained in this document should be performed by a qualified ShoreStation technician who understands the 
proper techniques and applications of the equipment used during the assembly process.  

Safety Definitions 

Safety messages are presented throughout this document and labels affixed to the product. The messages alert you to potential 

hazards to you and/or property. The signal words DANGERWARNING, and CAUTION are preceded by an alert symbol

 and 

communicate the severity of potential hazard. The severity of each type of message is defined as follows: 

 

DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury. 

 

WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury. 

 

CAUTION, used with the safety alert symbol, indicates a hazardous situation which, if not avoided, could result in minor or moderate 
injury. 

 

 

 WARNING 

DO NOT ATTEMPT TO ASSEMBLE THIS SYSTEM WITHOUT FIRST STUDYING THIS MANUAL AND 
INFORMATION ON LABELS INCLUDED WITH THE SYSTEM. FAILURE TO DO SO CAN LEAD TO IMPROPER 
OPERATION RESULTING IN SERIOUS PERSONAL INJURY AND/OR PRODUCT DAMAGE. IF YOU HAVE 
FURTHER QUESTIONS AFTER REVIEWING THIS INFORMATION, CONTACT A SHORESTATION 
REPRESENTATIVE AT (800) 859-3028. 

Summary of Contents for ShoreScreen CS270-102-7B


















Reviews: