background image

-54-

Model W1842 (For Machines Mfd. Since 6/17)

SE

RV

IC

E

Positioning.Chip.Deflector

Chip Deflector Gap Setting ............................

1

8

"–

1

4

"

The chip deflector directs chips and dust into the dust 

hood and prevents chips from falling back into the planing 

area. It is an orange plastic plate located under the top 

cover.

Tool.Needed:

Open-End Wrench 10mm.......................................1

To.adjust.chip.deflector,.do.these.steps:

1.  DISCONNECT MACHINE FROM POWER!

2.

  Remove (3) flange bolts shown in 

Figure.56.

and 

remove dust hood assembly.

3.

  Loosen (3) flange bolts securing chip deflector 

(see 

Figure.57

).

4..

Position chip deflector with a 

1

4

" gap 

(see 

Figure.57

)

.

between knives and deflector if 

planer/moulder is attached to a dust collection 

system. (Use a 

1

8

" gap if you are not using a dust 

collector.)

.

Make sure beveled edge of deflector faces 

cutterhead.

 

IMPORTANT:

 Remove the chip deflector before 

performing moulding operations.

5.

  Tighten flange bolts securing chip deflector 

(see 

Figure.57

).

6.

  Replace dust hood assembly and tighten (3) flange 

bolts shown in 

Figure.56

.

7.

  Loosen wing nuts (see 

Figure.56

)

.

that hold chip 

guide. For planer knives, slide chip guide to outfeed 

table side of slots. For moulding knives, slide chip 

guide to infeed table side of slots. 

8.

  Tighten wing nuts to secure chip guide.

Figure.56.

 Location of fasteners for 

removing dust hood.

Figure.57.

 Chip deflector re-installed.

Cutterhead

Chip Deflector

Flange Bolts

Flange Bolts

Chip Guide Wing Nuts

Summary of Contents for W1842





































































Reviews: