background image

15

OPERATING LOG SET

 

FOR YOUR SAFETY

 

 

READ BEFORE LIGHTING

 

 WARNING: If you do not follow 

 

LIGHTING

 

INSTRUCTIONS

    WARNING: Damper handle will  be 

hot  if  heater  has  been running.  

these instructions exactly, a 

fire

  or 

explosion  may  result causing prop-

erty damage, personal injury or loss 

of life.  

 

1.

 

STOP! Read the safety information from this page

column 1.

2.

 

Make sure equipment shutoff valve is fully open..

3.

 

Set selector switch in the OFF position.

    WARNING: Burners will come on 

 

 

   

 

 

automatically within one minute after

the pilot is lit, when the selector switch 

is in the on position

 

REMOTE - 

MODELS

   

A. 

follow these instructions exactly.

B.  BEFO RE LIGHTING smell all around  the 

• Do not try to light any appliance.

use any phone in your building.

 

• 

the fi

re department.

C. 

D. 

has been under water.

 gas control knob. Never use tools. If the 

Do not use this appliance if any part has 

knob will not push in or turn by hand, don’t 

try to repair it, call a qualified service tech-

nician or gas supplier. Force or attempted 

been under water. Immediately call a 

qualified service technician to inspect the 

appliance and to replace any part of the 

control system and any gas control which 

This appliance has a pilot which must be 

  lighted by hand. When lighting the pilot, 

appliance area for gas. Be sure to smell next 

to the floor because some gas is heavier than 

air and will settle on the floor.

• Do not touch any electric switch; do not 

• Immediately call your gas supplier from a 

  neighbor’s phone.Follow the gas

supplier’s instructions.

repair may result in a fire or explosion.

Use only your hand to push in or turn the 

If you cannot reach your gas supplier, call

WHAT TO DO IF YOU SMELL GAS

WARNING:

ions      

before running heater.   

sure fireplace screen is closed 

a fireplace screen in place. Make 

 You must operate this heater with 

across openings of fireplace.

fireplace will cause glass to burst. 

doors closed, heat buildup inside 

closed. If you operate heater with 

 If fireplace has glass doors, never 

operate this heater with glass doors 

Make sure there are no obstruct

 

a     

few hours.

Note:

 

 

heater with the chimney damper closed.

 

This will put

 

 

 

all the heat into the room. However, there may be times 

 

 

 

 

 

 

 

 

 

the chimney damper (if you have one) fully or partial-

Homeowners generally prefer to operate their

you will desire the full flames of the HI heat setting, 

but will find the heat output excessive. You can open 

heater, burning logs will give off a 

paper-burning smell. Orange flame will 

also be present. Open damper or win-

dow to vent smell. This will only last 

ly to release some of the heat. 

NOTICE: During initial operationof new 

Summary of Contents for Premier Estate PEVFR18LP

























Reviews: