Shinko CHC-S1245-5 Manintence Parts Replacement Procedure Download Page 12 | Manualshive

Page: 12 / 43

background image

YQE8-J0093E

9

Maintenance Parts Replacement Procedures

1

／

2

Parts

Name

Thermal Head Assy

Part No.

164-11-09770

Tools

Phillips Screwdriver (#2)

[Step 1] Remove 2 screws (M3x6) which hold the head gear cover, remove 2 screws (M3x6) which

hold the head open lever, and remove the head gear cover and head open lever.

[Step 2] Loosen 2 screws (1 for right and left each) (M3x6) which hold the head mount lever at both

dies of Thermal Head.

[Step 3] Remove 2 connectors at the Thermal Head Assy, and remove 1 screw (M4x8) which holds

the Thermal Head Assy.

Head Open Lever

Connector (CN22, CN23)

Screw

Screw

Caution: Do not loosen wrong screws.

Head Gear Cover

Screw

Screw

Screw

«
...
10
11
12
13
14
...
»

Summary of Contents for CHC-S1245-5












































Reviews:

No comments

Related manuals for CHC-S1245-5

Brand: Canon Pages: 11

Brand: Canon Pages: 2

Brand: Canon Pages: 12

PIXMA Pro9000 Mark II Series

Brand: Canon Pages: 4

Brand: VASTEX Pages: 15

Brand: G3D Pages: 4

Brand: Javelin Pages: 2

Brand: MakerBot Pages: 48

Brand: Samsung Pages: 368

Brand: Canon Pages: 34

Brand: Canon Pages: 369

Brand: NEC Pages: 10

Brand: Xerox Pages: 44

Brand: Printronix Pages: 9

5550B - Phaser B/W Laser Printer

Brand: Xerox Pages: 117

WorkCentre 3345

Brand: Xerox Pages: 18

Brand: BIO RAD Pages: 61

Brand: Tektronix Pages: 42

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands