Shindaiwa T302 Operator'S Manual Download

Page: 6 / 44

SAFETY

T302

X7502350700

The safety alert symbol accompanied by the word “CAUTION”
calls attention to an act or condition which may lead to minor or
moderate personal injury if not avoided.

The enclosed message provides information necessary for the
protection of the unit.

Note: This enclosed message provides tips for use, care and

maintenance of the unit.

CIRCLE AND SLASH SYMBOL
This symbol means the specific action shown is prohibited.
Ignoring these prohibitions can result in serious or fatal injury.

International Symbols

Symbol

Description

Symbol

Description

Warning, See

Operator’s Manual

Carburetor Adjustment -

High Speed Mixture

Wear Eye, Ear and

Head Protection

Carburetor Adjustment -

Idle Speed

Wear Hand

and Foot Protection

Carburetor Adjustment -

Low Speed Mixture

Safety/Alert

Emergency Stop

Hot Surface

Fuel and Oil Mixture

T
L

Summary of Contents for T302













































Search results

Summary of Contents for T302

Reviews:

Related manuals for T302

Brands by name

Popular brands

Shindaiwa T302, Operator'S Manual

Search results

Summary of Contents for T302

Reviews:

Related manuals for T302

Brands by name

Popular brands