manualshive.com logo in svg

Shindaiwa T302, Operator'S Manual

Share
Download
Shindaiwa T302 Operator'S Manual Download Page 35

T302

MAINTENANCE

X7502350700

35

© 4/2018 ECHO Inc.

ENGLISH

2.

Remove plug (A) and check 
level of grease.

3.

Add grease if necessary. DO 
NOT over-fill.

Drive Shaft

1.

Loosen screw (B) and remove 
locating screw (C). Pull gear 
case and shieldfrom drive shaft 
housing.

2.

Pull flexible cable from the drive 
shaft housing, wipe clean and 
re-coat with 15 ml  (0.5 oz.) of 
grease.

3.

Slide the flexible cable back in the drive housing. DO NOT get dirt on 
the flex cable.

4.

Install the gear housing and shield assembly.

Nylon Line Head Disassembly Instructions

Note: For normal use, Speed Feed

®

 head disassembly is not 

necessary. However, if circumstances require disassembly, 
follow these instructions.

1.

Press top of locking tabs (A) on 
both sides of Speed Feed

®

 

head to release cover (B) from 
eyelet carrier (C).

2.

Remove cover from eyelet 
carrier.

Nylon Line Replacement

Wear gloves or personal injury may result:

◆

Cutoff knife is sharp.

B

C

A

B

A

C

Summary of Contents for T302













































Reviews:

No comments

Brands by name

Popular brands

Load more brands