Shindaiwa T302 Operator'S Manual Download | Manualshive

Page: 36 / 44

background image

MAINTENANCE

T302

36

X7502350700

© 4/2018 ECHO Inc.

◆

Gearcase and surrounding area may be hot.

1.

Cut one piece of line to
recommended length.
2.0 mm (0.080 in.) diameter
7.6 m (25 ft.).
2.4 mm (0.095 in.) diameter
7.6 m (25 ft.).

2.

Align arrows on top of knob with
openings in eyelets.

3.

Insert one end of trimmer line
into an eyelet, and push line
equal distance through trimmer
head.

4.

Hold trimmer head while
turning knob clockwise to wind
line onto spool until about
13 cm (5 in.) of each line
remains exposed.

Trimmer head is now fully loaded
and ready for operation.

«
...
34
35
36
37
38
...
»

Summary of Contents for T302













































Reviews:

No comments

Related manuals for T302

Brand: LAAWA Pages: 14

Brand: Yardworks Pages: 22

Brand: Homelite Pages: 42

Brand: Stiga Pages: 308

Brand: Gama Garden Pages: 28

Brand: Mi-Heat Heizsysteme Pages: 4

sunjoe 24V-ST14B-CT

Brand: SNOWJOE Pages: 60

Brand: Philips Pages: 2

Brand: Leviton Pages: 2

Brand: Work Pro Pages: 4

Brand: Work Pro Pages: 6

Brand: Draper Pages: 3

Yard Machines Y26SS

Brand: MTD Pages: 56

Yard Machines Y700VP

Brand: MTD Pages: 64

Brand: GreenWorks Pro Pages: 21

60V UltraPower PH60L00

Brand: GreenWorks Pro Pages: 24

Brand: GreenWorks Pro Pages: 30

Brand: McCulloch Pages: 80

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands