Shindaiwa T302 Page 20 Operator'S Manual Download | Manualshive

Page: 20 / 44

background image

OPERATION

T302

20

X7502350700

© 4/2018 ECHO Inc.

◆

WEAR SAFETY GLASSES when mixing or handling.

◆

AVOID repeated or prolonged skin contact

◆

AVOID inhaling oil mists or vapors.

Shindaiwa brand 2-stroke oils may be mixed at 50:1 ratio for
application in all Shindaiwa engines sold in the past, regardless of
ratio specified in those manuals.

Handling Fuel

Fuel is VERY flammable. Use extreme care when mixing, storing
or handling, or serious personal injury may result.

◆

Use an approved fuel container.

◆

DO NOT smoke near fuel.

◆

DO NOT allow flames or sparks near fuel.

◆

Fuel tanks/cans may be under pressure. Always loosen
fuel caps slowly allowing pressure to equalize.

◆

NEVER refuel a unit when the engine is HOT or RUNNING!

◆

DO NOT fill fuel tanks indoors. ALWAYS fill fuel tanks
outdoors over bare ground.

◆

DO NOT overfill fuel tank. Wipe up spills immediately.

◆

Securely tighten fuel tank cap and close fuel container
after refueling.

◆

Inspect for fuel leakage. If fuel leakage is found, do not
start or operate unit until leakage is repaired.

◆

Move at least 3 m (10 ft.) from refueling location before
starting the engine.

Gasoline vapor is heavier than air, and can travel along the
ground to nearby sources of ignition such as electrical motors,
pilot lights, and hot or running engines. Vapors ignited by an
ignition source can flash back to the fuel container, resulting in
an explosion, fire, serious or fatal injuries, and extensive
property damage.

«
...
18
19
20
21
22
...
»

Summary of Contents for T302













































Reviews:

No comments

Related manuals for T302

Brand: Makita Pages: 12

Z-trimmer ZT-3000

Brand: Peco Pages: 12

Brand: Ryobi Pages: 20

Brand: Shindaiwa Pages: 16

Brand: Little Wonder Pages: 13

Brand: Makita Pages: 100

Brand: Blaupunkt Pages: 24

Brand: Hoberg Pages: 68

Brand: TIS Pages: 6

Brand: Leviton Pages: 2

Brand: Draper Pages: 22

00096-72.077.01

Brand: McCulloch Pages: 86

Brand: Jonsered Pages: 6

Brand: Jonsered Pages: 40

Ferrex FPLT-254 E1

Brand: ALDI Pages: 31

Brand: VITO GARDEN Pages: 16

Brand: Yardworks Pages: 26

Brand: Raider Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands