manualshive.com logo in svg

Shindaiwa T302, Operator'S Manual

Share
Download
Shindaiwa T302 Operator'S Manual Download Page 12

SAFETY

T302

12

X7502350700

© 4/2018 ECHO Inc.

Read Manuals

• Provide All Users Of This Equipment With Literature For Instructions On 

Safe Operation.

Clear The Work Area

• Always Clear The Work Area Of Foreign Objects, And Check For Any 

Hidden Hazards. Spectators And Fellow Workers Must Be Warned, And 
Children And Animals Prevented From Coming Nearer Than 15 M (50 Ft.) 
While The Unit Is In Use.

Keep A Firm Grip

• Always Hold Throttle Handle And Support Handle With Thumbs And 

Fingers Tightly Encircling The Handles.

Keep A Solid Stance

• Maintain Footing And Balance At All Times. Do Not Stand On Slippery, 

Uneven Or Unstable Surfaces. Do Not Work In Odd Positions Or On 
Ladders. Do Not Over Reach.

Avoid Hot Surfaces

• Keep Exhaust Area Clear Of Flammable Debris. 

Avoid Contact During And Immediately After 
Operation.

Equipment

Use only ECHO, INC. attachments. Serious injury may result 
from the use of a non-approved attachment combination. ECHO, 
INC. will not be responsible for the failure of cutting devices, 
attachments or accessories which have not been tested and 
approved by ECHO, INC. Read and comply with all safety 
instructions.

◆

Check unit for loose or missing nuts, bolts, and screws. 
Tighten or replace as needed.

◆

Inspect shield for damage and ensure that shield is 
properly installed, and that  that the cut-off knife is 
securely in place. Replace if either is damaged or missing.

◆

Check that the cutting attachment is firmly attached and in 
safe operating condition.

Summary of Contents for T302













































Reviews:

No comments

Brands by name

Popular brands

Load more brands